新研制開發氣動沖床效率*高,穩定性*好且大大降低生產成本和維修費用。

邊梁冷彎成型設備制造質量控制情況
根據客戶的要求,結合我公司生產部、質檢科實際情況,對于設備的生產管理、質量控制情況,作出以下介紹:
1、生產管理:
由生產經理統籌規劃,攜2名生產計劃調度員,合理安排各工序工作,保證加工車間、裝配車間、質檢科等各相關科室的工作順利進行,已使所有工序零部件質量達到貴司產品質量要求。
2、質量控制:
⑴、設備外觀:
①、設備整體表面整潔,油漆噴涂均勻完整,不流淌、無漏噴。軋輥表面、各導軌面、滑動面、滾動面及圖紙有要求的位置不能噴漆。
②、未噴漆部位涂防銹油,軋輥模具等重要部件無磕碰劃傷現象。
③、整機外漏部件除刃口外都作倒角、倒愣處理,去除尖角毛刺。
④、整機各焊接及裝配固定組件保證其與相關部件的相對位置合理、準確。
⑵產品精度:
①、標準軋機的牌樓固定螺栓、橫梁固定螺栓、軋輥軸鎖緊螺母、基準鎖緊螺母、軸承蓋緊固螺栓等一定要緊固到位,軋輥軸與軋輥基準線要垂直,允差0.2~0.3/1000,不可累積。
②、安裝校直架時要保證其中心與軋輥基準中心對正,保證左右調整間隙能滿足型材彎曲的調整及多種規格型材的共用。
Manufacturing quality Control of Cold forming equipment for side Beam
According to the requirements of our customers, combined with the actual situation of our production department and quality inspection department, we will introduce the production management and quality control of the equipment.
1. Production management:
By the production manager overall planning, with 2 production planning dispatchers, reasonable arrangement of each process work, to ensure the processing workshop, assembly workshop, quality inspection department and other relevant departments work smoothly, Has made all the process parts quality up to your product quality requirements.
2. Quality control:
1. Device appearance:
1, the overall surface of the equipment clean, paint spray uniform integrity, no flow, no leakage spray. Roll surface, guide surface, slide surface, rolling surface and drawing must not be sprayed.
2. The anti rust oil is not painted at the painting part, and the important parts such as the roll die and so on are not scratched.
3. The external leakage parts of the whole machine are all chamfered except the cutting edge, so as to remove the burr of the sharp angle.
4. The relative position of welding and assembling fixed components is reasonable and accurate.
2 Product precision:
1. The fixed bolt of the standard rolling mill, the fixed bolt of the transverse beam, the lock nut of the roller shaft, the base lock nut, the fastening bolt of the bearing cover must be fastened in place, the roll shaft and the roller datum line should be vertical, and the allowance is 0.2~0.3/1000, not to be accumulated.
2. When installing the straightening frame, it is necessary to ensure the alignment between the center and the roller reference center, and to ensure that the left and right adjustment clearance can meet the profile bending adjustment and the sharing of many kinds of profiles.

立體車庫邊梁全自動冷彎成型機主機傳動部分采用主電機和分部傳動的方式,每一道軋輥都有單獨的分配箱傳動,確保設備使用壽命和精度。

氣動沖床的增加既提高了工作效率又為客戶增加了選擇的空間,滿足不同客戶的需求。
-/gjeijh/-
http://www.dcago.com