邊梁冷彎成型設備制造質量控制情況
根據客戶的要求,結合我公司生產部、質檢科實際情況,對于設備的生產管理、質量控制情況,作出以下介紹:
1、生產管理:
由生產經理統籌規劃,攜2名生產計劃調度員,合理安排各工序工作,保證加工車間、裝配車間、質檢科等各相關科室的工作順利進行,已使所有工序零部件質量達到貴司產品質量要求。
2、質量控制:
⑴、設備外觀:
①、設備整體表面整潔,油漆噴涂均勻完整,不流淌、無漏噴。軋輥表面、各導軌面、滑動面、滾動面及圖紙有要求的位置不能噴漆。
②、未噴漆部位涂防銹油,軋輥模具等重要部件無磕碰劃傷現象。
③、整機外漏部件除刃口外都作倒角、倒愣處理,去除尖角毛刺。
④、整機各焊接及裝配固定組件保證其與相關部件的相對位置合理、準確。
⑵產品精度:
①、標準軋機的牌樓固定螺栓、橫梁固定螺栓、軋輥軸鎖緊螺母、基準鎖緊螺母、軸承蓋緊固螺栓等一定要緊固到位,軋輥軸與軋輥基準線要垂直,允差0.2~0.3/1000,不可累積。
②、安裝校直架時要保證其中心與軋輥基準中心對正,保證左右調整間隙能滿足型材彎曲的調整及多種規格型材的共用。
nufacturing quality Control of Cold forming equipment for side Beam
According to the requirements of our customers, combined with the actual situation of our production department and quality inspection department, we will introduce the production nagement and quality control of the equipment.
1. Production nagement:
By the production nager overall planning, with 2 production planning ditchers, reasonable arrangement of each process work, to ensure the processing workshop, assembly workshop, quality inspection department and other relevant departments work oothly, Has de all the process parts quality up to your product quality requirements.
2. Quality control:
1. Device appearance:
1, the overall suce of the equipment clean, paint spray uniform integrity, no flow, no leakage spray. Roll suce, guide suce, slide suce, rolling suce and drawing must not be sprayed.
2. The anti rust oil is not painted at the painting part, and the important parts such as the roll and so on are not scratched.
3. The external leakage parts of the whole chine are all chamfered except the cutting edge, so as to remove the burr of the sharp angle.
4. The relative position of welding and assembling fixed components is reasonable and accurate.
2 Product precision:
1. The fixed bolt of the standard rolling mill, the fixed bolt of the transverse beam, the lock nut of the roller shaft, the base lock nut, the fastening bolt of the bearing cover must be fastened in place, the roll shaft and the roller datum line should be vertical, and the allowance is 0.2~0.3/1000, not to be accumulated.
2. When installing the straightening frame, it is necessary to ensure the alignment between the center and the roller reference center, and to ensure that the left and right adjustment clearance can meet the profile bending adjustment and the sharing of ny kinds of profiles.
邊梁冷彎成型機主要參數:
(1)20道主輥, 1套校直裝置,1組導向裝置;
(2)過料寬度:500 mm;
(3)軋制厚度:3~4mm(可定制);
(4)軋制速度:0~4米/min可調;
(5)主軸直徑ф100mm;
(6)驅動電機功率:18.5KWx2
(7)機組組成:由:機身、牌坊組件、導向裝置、校直裝置、傳動系統組成。
in parameters of side beam cold forming chine:
(1) 20 in rollers, 1 set of straightening devices and 1 set of guiding devices;
(2) the ximum overloading width of 1: 500 mm;
(3) the rolling thickness is 3mm and 4mm(customizable);
(4) the rolling speed can be adjusted from 0 to 4 m / min;
(5) Spindle diameter of 100 mm;
(6) Drive motor power: 18.5KWx2
(7) Unit composition: by: fuselage, archway assembly, guide device, straightening device, tranission system.

立體車庫邊梁滾壓成型線-車庫邊梁輥壓成型線(濰坊奧騰冷彎機械有限公司)山東立體車庫邊梁生產設備-立體車庫邊梁冷彎機
http://www.dcago.com